|
|
Ron Reid![]() Inner circle Phoenix, Arizona 2733 Posts ![]() |
Hello All:
I'm trying to find replacement tubes for a Ken Brooke Multiplying bottle set. The current tubes are a bit beat up, so I'd like to replace them if I can. The current tubes are PVC, I am pretty sure. I've done quite a bit a searching and know that sch 40 has walls that are too thick. I found a number of places that advertise "thinwall" pvc tubing. Do you think the following tubing will be okay? Here's the link: (Sorry...for some reason, the Magic Café system won't provide a link for the full address) http://flexpvc.com/cart/agora.cgi?produc......35-4inch The inside diameter of my current tubes is 3.75 inches. The ID of the tubes on the website is 3.89. Do you think this will make a difference? Thanks for any help or advice you're able to give. Ron |
hugmagic Inner circle 7674 Posts ![]() |
I would get some Sintra plastic about 1 or 2 mm and make my own.
Richard
Richard E. Hughes, Hughes Magic Inc., 352 N. Prospect St., Ravenna, OH 44266 (330)296-4023
www.hughesmagic.com email-hugmagic@raex.com Write direct as I will be turning off my PM's. |
Michael Baker Eternal Order Near a river in the Midwest 11172 Posts ![]() |
Richard, how would you make the seam? I am not familiar with the use of plastics.
~michael baker
The Magic Company |
hugmagic Inner circle 7674 Posts ![]() |
It is glued. I would use pliobond or a similar flexible contact cement.
Sintra comes in a great variety of colors and thicknesses.
Richard E. Hughes, Hughes Magic Inc., 352 N. Prospect St., Ravenna, OH 44266 (330)296-4023
www.hughesmagic.com email-hugmagic@raex.com Write direct as I will be turning off my PM's. |
Michael Baker Eternal Order Near a river in the Midwest 11172 Posts ![]() |
OK, thanks!
~michael baker
The Magic Company |
Ron Reid![]() Inner circle Phoenix, Arizona 2733 Posts ![]() |
Thanks, Richard. That's something to look into. Would the tubes be perfectly round if done with sheets of Sintra?
Ron |
hugmagic Inner circle 7674 Posts ![]() |
If you glue them up around a form, let them try. Hit them briefly with a hot air dryer or heat gun they should take the heat into the material develop a memory.
Richard E. Hughes, Hughes Magic Inc., 352 N. Prospect St., Ravenna, OH 44266 (330)296-4023
www.hughesmagic.com email-hugmagic@raex.com Write direct as I will be turning off my PM's. |
Walking Bob![]() Elite user 500 Posts ![]() |
Hi Ron
Go to a carpet store and look at the cardboard cylinders that the carpet is rolled up on. They are very durable, don't really seem like cardboard and could be painted and or finished nicely. Just a possibly idea, Walking Bob in Iowa |
Pete Biro![]() 1933 - 2018 18558 Posts ![]() |
Why not cover the old tubes with stick on vinyl? That's what I did.
![]()
STAY TOONED... @ www.pete-biro.com
|
Ron Reid![]() Inner circle Phoenix, Arizona 2733 Posts ![]() |
Thanks for the ideas Bob and Pete. I want to try getting some of the PVC tubing first because that's what I think I like best. I may explore your suggestions as well as Richard's.
Ron |
IDOTRIX![]() Elite user Darien,il 467 Posts ![]() |
I'd love to see these when they are finished. I still want you to redo mine when I get the dents out. Mike
|
Riley![]() Special user Swansea UK 955 Posts ![]() |
Go to the plumbing section and buy PVC down pipe. That is what Ken supplied.
![]() |
R Don![]() Regular user West Coast 197 Posts ![]() |
The UK pluming shops might have a good match but I
have never seen same in Canada; only thick wall tubing. |